M1K3 FX

M1K3 FX Special Effects Makeup, Set Design & Construction, Practical Prop Making, and much more! [email protected]

Coming soon: M1K3's own haunted attraction!

With 35+ years of combined experience, M1K3 FX is your one-stop shop for all of your entertainment needs!

10/05/2018

Beautiful!!!

10/05/2018

What do you all think? Are you excited to see this??

09/09/2017

Have any of you used one of these? Thoughts? Tips and tricks?

08/31/2017
Mortikai's -  CoGo Studio (M1K3 FX) Shop Tip Saturday! Here is a little something I put together this year.   With almos...
10/08/2016

Mortikai's - CoGo Studio (M1K3 FX) Shop Tip Saturday!

Here is a little something I put together this year. With almost 30 fog machines to fill daily over a 90 acre property, it became quite a chore so I utilized a portable fuel pump and added a meter so I can monitor which zones use how much fog juice. Just drop the suction tube into the barrel and then drive right up to the pails and fill them with the nozzle. What used to take a team of six technicians more than 2 hours to complete hauling pails back and forth and hand pumping from the barrel, I can now complete by my self in 90 minutes.

Got a tip you would like to see showcased? Send us a message and we'll give you a shout out.

Like this tip? Then "LIKE" this tip! Don't forget to SHARE it with a friend to help them out or leave a COMMENT! Be sure sure to "LIKE" the page, too, so you don't miss next week's Shop Tip Saturday!

-Mortikai

Mortikai's -  CoGo Studio (M1K3 FX) Shop Tip Saturday! When making an inside corner measurement don't bend the tape it i...
10/01/2016

Mortikai's - CoGo Studio (M1K3 FX) Shop Tip Saturday!

When making an inside corner measurement don't bend the tape it is more accurate to add the length of the body of the tape measure. Most tape measures are 3" so simply add 3" to the measurement that reads on the tape. The length of the body of the tape is usually printed on the bottom of the tape measure.

Got a tip you would like to see showcased? Send us a message and we'll give you a shout out.

Like this tip? Then "LIKE" this tip! Don't forget to SHARE it with a friend to help them out or leave a COMMENT! Be sure sure to "LIKE" the page, too, so you don't miss next week's Shop Tip Saturday!

-Mortikai

Mortikai's -  CoGo Studio (M1K3 FX) Shop Tip Saturday! Quick easy way to mark a line for cutting a board.  Don't use thi...
09/24/2016

Mortikai's - CoGo Studio (M1K3 FX) Shop Tip Saturday!

Quick easy way to mark a line for cutting a board. Don't use this tip if your measurements need to be dead on accurate but for cuts that allow a little wiggle room this will speed up marking lines dramatically. In one hand hold the marking device to the end of the tape and the other hand place your finger at the desired distance on the tape and along side the board and slide both hands straight with the tape to mark the board.

Got a tip you would like to see showcased? Send us a message and we'll give you a shout out.

Like this tip? Then "LIKE" this tip! Don't forget to SHARE it with a friend to help them out or leave a COMMENT! Be sure sure to "LIKE" the page, too, so you don't miss next week's Shop Tip Saturday!

-Mortikai

Mortikai's -  CoGo Studio (M1K3 FX) Shop Tip Saturday! Got a stripped screw?   This tip might just save the day.   A rub...
09/17/2016

Mortikai's - CoGo Studio (M1K3 FX) Shop Tip Saturday!

Got a stripped screw? This tip might just save the day. A rubber band gives a little more grip and just might be enough to get that screw to start turning.

Got a tip you would like to see showcased? Send us a message and we'll give you a shout out.

Like this tip? Then "LIKE" this tip! Don't forget to SHARE it with a friend to help them out or leave a COMMENT! Be sure sure to "LIKE" the page, too, so you don't miss next week's Shop Tip Saturday!

-Mortikai

Mortikai's -  CoGo Studio (M1K3 FX) Shop Tip Saturday! Need a little more leverage on your wrench?   Hook the closed end...
09/10/2016

Mortikai's - CoGo Studio (M1K3 FX) Shop Tip Saturday!

Need a little more leverage on your wrench? Hook the closed end of a second wrench into the open end of the wrench on the bolt and increase your leverage power and reach. Take extra care in utilizing this tip as adding extra leverage with this method or a breaker bar always adds a higher level of risk and while the wrenches interlock they still can slip apart.

Got a tip you would like to see showcased? Send us a message and we'll give you a shout out.

Like this tip? Then "LIKE" this tip! Don't forget to SHARE it with a friend to help them out or leave a COMMENT! Be sure sure to "LIKE" the page, too, so you don't miss next week's Shop Tip Saturday!

-Mortikai

Mortikai's -  CoGo Studio (M1K3 FX) Shop Tip Saturday! Here's a quick easy tip to make that tangled mess of cords a litt...
09/03/2016

Mortikai's - CoGo Studio (M1K3 FX) Shop Tip Saturday!

Here's a quick easy tip to make that tangled mess of cords a little more manageable. Got multiple tools plugged in and find yourself having to trace back cords to find which cord your plug is attached to? Color code either end of the cord to make them easy to find.

Got a tip you would like to see showcased? Send us a message and we'll give you a shout out.

Like this tip? Then "LIKE" this tip! Don't forget to SHARE it with a friend to help them out or leave a COMMENT! Be sure sure to "LIKE" the page, too, so you don't miss next week's Shop Tip Saturday!

-Mortikai

Sure there is always dumpster diving for those no price is the best price items,  but what if there was a place where th...
08/27/2016

Sure there is always dumpster diving for those no price is the best price items, but what if there was a place where those items were housed in a warehouse store in one easy to shop location. Search for a local reuse center, the items will cost a little bit it's hard to beat the convenience.

Mortikai's -  CoGo Studio (M1K3 FX) Shop Tip Saturday! Easy way to mark cut lines.    Drill a small hole at the one inch...
08/20/2016

Mortikai's - CoGo Studio (M1K3 FX) Shop Tip Saturday!

Easy way to mark cut lines. Drill a small hole at the one inch mark big enough for the tip of a pencil and then just add one inch to your measurements to account for the one inch taken away for the hole that was drilled.

Got a tip you would like to see showcased? Send us a message and we'll give you a shout out.

Like this tip? Then "LIKE" this tip! Don't forget to SHARE it with a friend to help them out or leave a COMMENT! Be sure sure to "LIKE" the page, too, so you don't miss next week's Shop Tip Saturday!

-Mortikai

Address

Shakopee, MN
55379

Alerts

Be the first to know and let us send you an email when M1K3 FX posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Establishment

Send a message to M1K3 FX:

Share