Deep Cuts Cutlery

07/25/2024

Yes chef. Right away jeff!

Quite pleased with this proto overall. 7.5" edge, 12" overall. .072" thick 8670 @ 63.5 HRC with a very thin, shallow, 6' diameter hollow grind. Balance point is right where the scales meet the ricasso.

This prototype will be part of a big Donation(RAF) Based Giveaway (FLE), that will be conducted thru my email list(you can sign up for email inventory notifications on my website to be added to the list).

I think I will order some Nitro-V for another small run of these. Would u be interested?

05/30/2024

Nitro-V Rascals available. Doin it a lil different this time. They're finish ground and scales are ready to go. You choose how you want scales attached, finish(belt satin, blasted, blast+tumble, darkwash), and sheath setup. I'm ordering kydex this weekend so you could request certain colors/patterns. These will be getting these finished out to the buyers specs next week. They start at $250 with removable scales and standard sheath, scales attached with flared tubes are +$25, and substituting a ambidextrous pocket sheath with a DCC clip is +$45.

These have a 2.5" edge, and are 6.3" overall. .108" Nitro-V stainless @ 63 HRC. Cryo cycled, wet ground, all the good stuff. Probably my fav EDC steel.

DM or comment if you'd like to claim one. PayPal payment preferred, but Zelle, Venmo, and Cashapp are all accepted.

05/15/2024

yeah I moved back to Minnesota and busted out the flannel immediately🤷‍♂️. There's currently still one or two of these Magnacut Little Rascals available on the website.

04/23/2024

Here's a lil different Midsized Rascal. There's only one at this time but may very well have to do some more finished in this fashion 🤔

🌟.110" CPM Cruwear Steel 64-65 HRC
🌟 in-house small batch custom heat treat with cryo cycling, focused on fine edge stability
🌟Torched Richlite Scales w/ flared stainless tubes with a hardened jute wrap over it.
🌟Distressed acid stonewash finish.
🌟3" blade, 7" overall
🌟 Includes ambidextrous pocket sheath in carbon fiber textured kydex.

4️⃣2️⃣0️⃣💰USD ship'd to the first to claim it via comment or DM🤙

Assuming this post will most definitely get flagged I'll likely be deleting this in the near future

02/08/2024

Some fun lil prototypes in 80CrV2 available. 2 with an acid/stonewash finish and one with black oxide finish.
095" blade stock
62-63 HRC. DET anneal + cryo
Hollow ground on 14" wheel
Approximately 2.25" cutting edge and just shy of 6"overall.
Richlite scales, GFlex epoxy, and stainless tubes
💲2️⃣1️⃣5️⃣ ship't (~ +💲20 for internationa).
DM or comment with to claim yours

02/08/2024

CPM 10-V prototype test blades. These were used for some rope cut testing, and evaluation to help fine tune and dial in my heat treatments for this alloy moving forward. I'm planning on doing a lot of 10V this year because it just packs such a stellar balance of properties for tool made to slice stuff. All 3 samples sharpened and performed great in rope cut testing. As you might expect the increasing hardness correlated with longer edge holding, tho the difference between these samples was pretty damn tight, I'd consider all of em pretty primo 10V🤌.

#1-66 HRC, #2-66.5 HRC, #3-67 HRC

Black Oxide and Distressed oxide finishs
.095" CPM 10-V all heat treated with cryo cycles & low and temper
3.5" edge, 8" overall
Half tang construction
Hollow ground nice and thin on 14" wheel
Richlite scales, G-Flex epoxy, & flared stainless tubes

#1-3️⃣1️⃣5️⃣/ #2-3️⃣2️⃣5️⃣/ #3-3️⃣3️⃣5️⃣ shipped (+20 for international shipping)

02/08/2024

CPM Cruwear prototypes available. #1 @ 63.9 HRC and #2 @ 64.8 HRC. Used some evaluation and cut testing to gimme a better idea of where I wanna run this in the future. Both sharpened/deburred and performed really well, the harder blade lost sharpness at a slightly slower rate as you may expect.
095" CPM Cruwear heat treated with cryo cycles and low and tempers
3.5" edge 8" overall
Half tang construction
Hollow ground on 14" wheel nice and thin
Acid etched finish
Richlite scales, G-Flex epoxy, stainless flared tubes

#1:💲3️⃣1️⃣5️⃣ // #2: 💲3️⃣2️⃣5️⃣ shipped(+20 for international shipping)

Comment or DM to claim

08/27/2022

Hollow Ground Big Rascal in Nitro-V. Wasn’t planning on the hollow grind when I stamped it that’s why the stamps are a lil wonk. Also available. $305 shipped

07/23/2022

Finishing out sheaths and final cleanup today on this batch of Little Rascals in CPM Magnacut. They're all sporting black burlap micarta scales and will have dark forest green kydex sheaths with brown soft loops. Available tomorrow, 2pm at www.deepcutscutlery.com

#🤠

03/24/2022

03/24/2022

Here's these two side by side. I don't know which one I like more. These are loose variations of a basic design I drew up based on what I'd want to have on my belt as a regular user these days. You'll see more one-offs like this periodically based on what I'm feeling like making.

They'll be listed on my website this evening.

03/24/2022

This one on is pretty much wrapped up too. ~ 4 7/8" of cutting edge and 9 7/16" overall. 5/32" A2 tool steel heat treated to 65.5-66 HRC and ground nice and thin, around .008" or so behind the edge. Black Richlite scales with black pins and a micarta lanyard tube. If I don't decide to make this one mine it'll be available on my website later this evening.