Norriss 1616

04/20/2026

Had to have it. Never seen this before. Would love to find the inch one.

04/20/2026

04/20/2026

Now that is a fart fan!

04/15/2026

Any ideas brakes are spongy still after changing the pads and rotors. Have bled the system 2/3 times all round but it's not making a difference. Can't see any leaks anywhere, there's plenty of fluid. Not sure what I've missed Pic is just for attention really!
🤔💬🛠️⚙️🚗 🤔💬

04/15/2026

He filled the tub and told me not to touch it for 24 hours. 🛑. I asked why. He said, 'That is a Hydro-Lock procedure. The weight of the water pushes the tub through the plywood so it locks into the floor joists permanently. If you drain it, the tub will float away.' FLOAT AWAY?? 🎈. It’s a 100-pound tub! I don't want it pushed through the floor into my kitchen! I feel like he’s trying to break my house. Do I pull the plug?

04/15/2026

Am I being too picky or did my fabricator mess up?
Had granite countertops installed. There are some issues and I’m wondering if it’s just me being picky or if I’m justified in being upset.
Here are the issues.
1. They were supposed to do a 3/8” outside edge profile on the corners and while it appears they did, the corners look really rough in my opinion. Like, the profile is not consistent from the side. It looks like they were manually ground down with some kind of grinder rather than water cut.
2. The sink cutout is also really rough in my opinion. It’s hard to get pics of it but it’s like there are some chipped areas on the underside and the curves aren’t smooth, they’re wavy/lumpy.
3. Faucet hole looks pretty off-center
Am I making a big deal of nothing?

04/15/2026

Thought I’d just throw some new rotors on today… yeah right. 3 hours later I’m out here swinging a hammer like a maniac and this rotor is laughing at me. Finally grabbed a gear puller, tore chunks out of it, used heat, soaked it in lube—still holding on for dear life. This thing is personal now. What’s the next move?? ⚙️🛠️🙆🤔💬🚗

04/15/2026

This Transit bolt is a stuck-nut nightmare 😤
This 2021 Ford Transit 350 is a real headache! My previous mechanic stripped out one of the caliper bracket bolts, and despite trying extractors, hammer and chisel, and an air hammer, it's still stuck fast. Seriously don't know where to begin with this one – has anyone else tackled this nightmare before and found a solution? 😩🔧❓

04/15/2026

Found a bowling ball! Will it fall off or stay on throughout the season?

04/15/2026

The dealership is really trying to tell me this belt needs to be replaced just because it has a few cracks in it
These belts are made out of high-grade rubber that’s designed to last the entire life of the vehicle and now they’re trying to charge me labor to swap it out like I don’t drive 160 miles a day already
If the belt was actually bad the car wouldn’t be running at all, but here it is still spinning like a champ so obviously it’s fine. The cracks just mean it’s broken in and flexible, not that it’s failing
$73.78 in labor to change a belt that clearly still works is insane in this economy. I’m not replacing something that isn’t broken just because they want to upsell me. 🤔💬🛠️

04/15/2026

Dull fact about my job. This is exactly one months worth of brake rotors that I personally have replaced myself this month. I took them all to the scrap metal yard this morning for a total of 1,400 lbs which is short of my usual 2,000+ lbs.
Gallon water jug for scale.

04/15/2026

What's causing this corrosion on my battery, and what can I do to fix it?
1989 Ford sF350 7.3 idi. This is the secondary battery, and it keeps corroding which is causing issues with starting. 🤔💬